1 Second Wireless Dental LED Curing Light Cure High Power Blue Lamp Curing Resin. ✨Product Principles: LED curing light uses the principle of light radiation, the photosensitive resin was cured by irradiation.
100 Brand new and high quality Dental Bur Block with Cover 16 Holes For FG RA Bur Fully autoclavable metal, Aluminum material Application: Used to place burs Features: With 16 holes, the bur block is designed for both high speed burs and low speed burs. Made of quality aluminum,disinfected, cleaned, sterilized and autoclavable under the high temperature of 135 ℃ The dental bur blocks assure a hygienic, ergonomic and economic procedure The special lids of the bur blocks protect the instruments against damage and prevent them from falling out of the tray A handy support in your dental office </pFDA Statement The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item. Seller name:dentistryshop City,State:SHENZHEN,China Telephone number:0755-23998164
Introduction: 1.Technical specifications： 1.1Dimensions: 25mm×25mm×240mm 1.2 Net weight: 280g 1.3 Power source 1.3.1 Power supply: rechargeable Lithium battery 1.3.2 Battery mode: ICR 18490 1.3.3 Battery voltage and capacity: 3.7V/ 1400mAh,Battery has protection against Over-voltage, over-current and short circuit. 1.3.4 Adapter Power Input: 100V to 240V, 50Hz/60 Hz Input Power: 10VA Power Output: DC5V/1A 1.4 Light source: 1.4.1 5W high power blue light LED 1.4.2 Checking method: the LED light is fine when the light is on during operating correctly. 1.4.3 The wave length of this product can match with the clinical dental resin solidification, such as 3M, Dentspl etc. 1.4.4 Wave length: 440nm-480nm 1.5 Light intensity: 1200mW/c㎡~1600mW/c㎡ 2. Operation： 2.1 Press the mode button. Following two modes are available. 2.1.1 TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds.Its output light intensity is about 1200 mW/c㎡-1600mW/cm2 2.1.2 NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5,10 ,15and 20 seconds.Its output light intensity is about 1200mW/c㎡-1600 mW/c㎡ 2.2 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OFF button and the main unit will produce "Bi" sound, the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce tone at every 5 seconds, it stops working when counting down to "0". 2.3 During operation, the blue light can be stopped by press the power button at any time. 2.4 After a working cycle, operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, do not restart until the equipment cool down. Suggest continues working cycle less than 10 times. 2.5 Low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of main unit will wink, please charge in time. 2.6 When the battery needs to be charged, connect the plug of the adapter into the AC100V~240V power supply. Then connect the output plug of the adapter to the DC 5.0V input plug of the pedestal, and then the logo turn to blue. Put the main unit to the charging point of the pedestal, the display screen turn to scrolling display, and the curing lights starts charging. 2.7 After operating, take off the disposable sleeve and throw away, forbidden to reuse. 2.8 This equipment will turn off automatically if don't any action within 2 minutes, turn it on by press any button. 2.9 The depth of solidification of composite is no less than 2mm per 1 second. Material:The handle is made of plastic，The lamp holder is made of metal FDA Statement The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item. Seller name:sinodental City,State:SHENZHEN,China Telephone number:0755-35590238
1S LED Curing Light Lamp. · 3 versatile curing modes for every indications. Mode selection ： P1, P2, P3. ·Produce the maximum light intensity safely. During clinical use, it is not suitable for deep base lining or pulp capping.
Dental resin materials commonly used in clinical practice can match the wavelength of this light curing. The commonly used clinical dental resin materials can match with the wavelength of this light curing, such as 3M, Dengsperm and other resins.
✨Product Principles: LED curing light uses the principle of light radiation, the photosensitive resin was cured by irradiation. ✈️1 XDental Curing Light. ✨Two Working Modes: P1 Highlight mode, P2 Standard mode.
· 3 versatile curing modes for every indications. Mode selection ： P1, P2, P3. · Produce the maximum light intensity safely. Intensity ： 800-1400mw/cm². Shade plate 1. Storage Condition: Temperature: +10℃+40℃.
Dental Curing Light 1 Sec Curing 7 Modes Intensity 2000mw Wide Spectrum. The wave length of this product can match with the clinical dental resin solidification, such as 3M. Press the mode button.Following Seven modes are available：.
